Page 1 of 1

How about a Colt 1917 Revolver?

Posted: Mon Sep 07, 2009 8:26 pm
by android
Looks very similar, and less expensive.
What do you guys think?
Image

Re: How about a Colt 1917 Revolver?

Posted: Mon Sep 07, 2009 9:16 pm
by alphared6
I have one. It's a great piece!

Image

Re: How about a Colt 1917 Revolver?

Posted: Thu Sep 24, 2009 9:38 am
by Dangerman009
Is that blued or nickel? I'm guessing it's blued. It looks very cool. :tup:

Re: How about a Colt 1917 Revolver?

Posted: Thu Sep 24, 2009 7:54 pm
by alphared6
Dangerman009 wrote:Is that blued or nickel? I'm guessing it's blued. It looks very cool. :tup:
Thanks, it was blued, but most of the bluing has come off over the years. I intend to keep it original as you see it.

Mike

Re: How about a Colt 1917 Revolver?

Posted: Sun Oct 18, 2009 10:57 am
by Luke Warmwater
That's a gorgeous piece, Mike. I also prefer an antiqued firearm that looks like it has stories to tell.

Re: How about a Colt 1917 Revolver?

Posted: Sun Oct 18, 2009 7:23 pm
by Chewbacca Jones
That is a really nice piece. Definitely best to keep the original finish. Re-bluing never bodes well for resale value. Not that one plans to part with something like that!

Re: How about a Colt 1917 Revolver?

Posted: Mon Oct 26, 2009 5:36 pm
by 191145
This will be controversial, so don't read unless you're open-minded. Concerning that very nice Colt. If it were mine, I would consider cold-bluing it, with no surface prep other than hot soap and water. As you know, cold blue is not hard to remove and is very easy to 'distress' or 'age' without affecting in any way the original steel surfaces. The point would be to have a more authentic-looking gun that would easily and quickly wear on the high spots for a great 'old' look. Cold blue can be nicely done in the right hands, but it does take some knowledge and experience. The only reason I mention this is because I'm getting ready to do just that to a 1918 Colt M1911 that has not one speck of finish remaining on the slide or frame. Its not extremely valuable either because of some very light pitting, worn-smooth grips and a pitted bore from early corrosive ammo and no cleaning. I'm going to put new grips on and age them back as well as a cold blue job to just make it more presentable. If anyone wanted to have it restored in the future, everything would be there just like it is today - pits, rust stains and all.
Image

Re: How about a Colt 1917 Revolver?

Posted: Mon Oct 26, 2009 10:24 pm
by M1917
If I may sir, I'd suggest a "brush blue" finish, which was correct for the era. The parts were brushed, but not high polished, which gave the blue more of a satin finish than a deep blue finish that Colts are famous for. It tends to wear off the high points, which give you holster wear while protecting the rest of the gun. An unmessed-with M1911 is an expensive piece, particularly if it is an all matching GI duffle gun.
R/S
Fritz

Re: How about a Colt 1917 Revolver?

Posted: Thu Apr 29, 2010 2:58 pm
by Indiana
PLEASE don't touch that 1911. It's too pretty as is.

Re: How about a Colt 1917 Revolver?

Posted: Mon Jun 21, 2010 7:53 am
by IndyMaster
I love your Colt. Where did you get it? :Plymouth: