My BCF: A first step

In-depth discussion of the Fedora of Indiana Jones and all other hats appearing in the Indiana Jones movies

Moderators: Indiana Jeff, Dalexs

Post Reply
Indyextra1
Dig Worker
Dig Worker
Posts: 17
Joined: Fri Jul 27, 2007 9:56 pm

My BCF: A first step

Post by Indyextra1 »

And my first Fedora!
I finally had an opportunity to get a $20 fedora from Burlington Coat Factory (the best that a teen without a job can get).
After about 2 weeks of shaping, I finally got the nerve to trim off the rolled brim. I'm going for mostly a Raiders look, with LC for the brim.

http://i3.photobucket.com/albums/y75/Cl ... C00468.jpg
http://i3.photobucket.com/albums/y75/Cl ... C00469.jpg

Any opinions or suggestions?
User avatar
Ripper
Professor of Archaeology
Professor of Archaeology
Posts: 948
Joined: Thu Jul 04, 2002 12:05 am
Location: Colorado

Post by Ripper »

Not bad for a first hat ! Its all over now, first a hat, then a better hat, then a jacket, then a better jacket and so on.............
:wink:

Welcome to the club by the way !
User avatar
Jaredraptor
Dig Leader
Dig Leader
Posts: 559
Joined: Tue Jun 05, 2007 9:37 pm
Location: Tanis, Egypt.........okay, really Alexandria VA

Post by Jaredraptor »

Hm........y'know, since I'm in the same boat as you, I may go get myself a BCF fedora and see what I can do with it (sure, I've got my modified Mayser, but I'd rather not risk screwing up the brim on that. or the Raiders style ribbon)
User avatar
eazybox
Professor of Archaeology
Professor of Archaeology
Posts: 1038
Joined: Sat May 12, 2007 5:04 am
Location: Brody's Barber Shop

Post by eazybox »

Try making the side creases less deep. That might help to lessen the taper. The crown would need to be taller for the Raiders look, but it's not bad for $20.00-- that's what a wool felt Stetson Indy cost in 1984.

Jack
User avatar
Dalexs
Site Admin
Site Admin
Posts: 9009
Joined: Mon Jul 08, 2002 2:49 am
Location: Jus' nath' of Bawstin
Contact:

Post by Dalexs »

If you do a search here for BCF, you'll see some amazing things that be be done with these hats.

I routinely stop by my local branch whenever I'm in the area.

Dalexs
User avatar
Arkansas Russell
Laboratory Technician
Laboratory Technician
Posts: 192
Joined: Wed Jan 04, 2006 4:03 pm
Location: The Arkansas Delta

Post by Arkansas Russell »

Very nice job!
User avatar
Dr.Seuss
Dig Leader
Dig Leader
Posts: 429
Joined: Fri Mar 02, 2007 8:49 am
Location: Crawling from a Rocky Mt. Silver Mine

Post by Dr.Seuss »

Tackling a hybrid, from the "get-go?" Gusty move, and, an admirable attempt.

Nice job!

Sincerely,
User avatar
JulianK
Archaeologist
Archaeologist
Posts: 373
Joined: Wed Jan 10, 2007 10:54 am
Location: Gatineau (Ottawa Area), Canada

Post by JulianK »

Definitely a good start! You'll be sanding Westeds in no time!! No lack of initiative here! :)
User avatar
indy89
Museum Curator
Museum Curator
Posts: 1254
Joined: Tue Aug 01, 2006 11:02 pm
Location: TX

Post by indy89 »

Nice lid! I have a couple of them BCF hats. They're great for starters. Welcome to the club!!
Indyextra1
Dig Worker
Dig Worker
Posts: 17
Joined: Fri Jul 27, 2007 9:56 pm

Post by Indyextra1 »

Thanks for the compliments and tips. I might wet it down one more time to try and get the shape right. As for sanding Westeds, not a chance in the next 4 years :wink:
I wore it to college classes today and was told that it looked like a cross between Indiana Jones and Humphrey Bogart :?
User avatar
Mac
Archaeologist
Archaeologist
Posts: 236
Joined: Thu Mar 16, 2006 11:11 pm
Location: The Carolinas

Post by Mac »

Indyextra1 that’s a great start! If you have the time, you might want to try taking a BCF hat:

Image

get some plaster and make one of these:

Image

and then turn your hat into this:

Image

You can dye the ribbon with brown RIT dye and that would take some of the sheen off and make the color more SA. Your total outlay for plaster, dye, and sandpaper for pouncing would be about $10.

No one would ever know that it’s a BCF; viewtopic.php?t=20934

- Mac
User avatar
Risu
Professor of Archaeology
Professor of Archaeology
Posts: 723
Joined: Sat Aug 25, 2007 9:19 am
Location: Sprandy of Little Chair

Post by Risu »

When I first saw one of those hats in BCF on black friday I thought to myself "Sweet jesus, that's a tiny, sad little hat." But that last pic is just plain amazing.
User avatar
ydam
Laboratory Technician
Laboratory Technician
Posts: 193
Joined: Sun Jul 01, 2007 10:02 pm

Post by ydam »

Yup...i have to say my jaw dropped when i saw what you did with your BCF lid Mac..would love to see Indyextra pull one of these off. For 20 buch though that is hard to beat...gratz on the hat Extra and keep us updated if you decide to pursue a reblock.
Indyextra1
Dig Worker
Dig Worker
Posts: 17
Joined: Fri Jul 27, 2007 9:56 pm

Post by Indyextra1 »

Man, that looks amazing!
I guess there would be no harm in trying it. I have a couple of questions, though.
First, how do you cast the plaster into the right shape for the block?
And second, how would I figure out the dimensions I would need?
The Pilot
Laboratory Technician
Laboratory Technician
Posts: 136
Joined: Thu Nov 22, 2007 1:30 pm
Location: The Great Green Pacific Northwest
Contact:

Post by The Pilot »

Mac wrote:Indyextra1 that’s a great start! If you have the time, you might want to try taking a BCF hat:

...

get some plaster and make one of these:

Image
Can you explain that in detail? How do you form it, and how do you use it?
User avatar
airforceindy
Laboratory Technician
Laboratory Technician
Posts: 181
Joined: Fri Aug 24, 2007 1:07 pm
Location: Anchorage

Post by airforceindy »

Ditto there! I would love to see the progress on your block shape, if you've been able to do some work to it since the original posting of those pics. Fantastic job, Mac! What are you using as your mold, an older hat? Or something like the now infamous Tupperware block (I can't quite recall who was responsible for that...)? You mentioned doing a tutorial on block making; that would be of great use and interest to all of us, I'm sure, particularly those of us who are a little slower getting into the whole hat thing and strapped for cash at the same time!

Highest Regards, Andy
User avatar
RobbyT43
Dig Leader
Dig Leader
Posts: 400
Joined: Fri Jun 01, 2007 11:04 pm
Location: Well depending on the time, I could be in one spot or several...
Contact:

Post by RobbyT43 »

Hey Indyextra1!!! Welcome to COW :wink:

Im a teen too...so I totally understand your situation becuase Im going through the exact same thing! Right now, the best advice I have gotten is to get a decent hat and then save up for a good one- one that you want.

Good luck :D

Robby
User avatar
Mac
Archaeologist
Archaeologist
Posts: 236
Joined: Thu Mar 16, 2006 11:11 pm
Location: The Carolinas

Post by Mac »

I’m afraid RobbyT43 is right - the best advice is to save up for a decent hat! But do-it-your-selfers and guys on a tight budget (read college students) can get by with a little ingenuity.

I’m away from home for the weekend, so I can’t take any photos for a proper tutorial but I can put together a mini tutorial and TRY to explain what I’ve done.

First I used a CAD program to draw an oval. The oval needs to be about 1.5 inches longer than it is wide and the circumference needs to be about 1 cm more than your head measurement. The program you use must be able to give you precise measurements for the circumference so you can scale it accurately and keep the 1.5 difference between width and length. I’m sure there are free programs available that can do this, but I used a simple (and obsolete but very easy to use) commercial program call Quickcad.

For a size 57 [57 cm circumference head; size 7 1/8], the width will be about 6.5 inches, and the length will be about 8 inches (note the 1.5 inch difference). For the width and length, draw a horizontal line 6.5 inches long and bisect with a 8 inch line to form a “+” shape. Then draw an oval over the “+”. Then scale the oval so that it is exactly 58 cm.

So the rule is (for a regular oval head), make the oval 1.5 wider than long, and make the circumference of the oval 1 cm more than your head size.

Print out your oval. Make sure that, in your printer preferences dialog, scaling is turned off, so that the oval will print to precisely the dimensions you want. Measure the print out height and width carefully to double check.

OK, if you’ve read this far and you’re not asleep, you’re ready make a form for your mold.

Carefully cut out your oval precisely on the line. Trace the cut on a piece of thick cardboard or flat styrofoam. Styrofoam is probably better, because it’s water proof. Cut out your tracing on the thicker material. I used cardboard, so I wrapped it with packing tape so that the water that drains from the plaster would not turn the cardboard into mush.

Once you have this new oval cut, you then wrap it with thick plastic to form a mold. I used a large “For Sale” sign, $2 at Walmart. It’s thick and will resist bending under the weight of wet plaster. Cut a strip about 7 inches in height and long enough in length to wrap around your oval.

Now, wrap the plastic around the oval and tape it up. Scribe a line on the inside of the plastic, 6 inches up from the bottom. This is how much plaster will go into the form.

For a size 57 block, you will need eight to ten pounds of plaster. Mix up the plaster and pour it in the block up to the fill line. Remember that extra cardboard oval; this is where you use it. Place it in the top of the form to stiffen the whole thing and keep the side walls straight. Here’s a picture:

Image

Wait a couple of days to make sure it dries completely; it should look like this:

Image

Then cut away the plastic (or carefully remove it to make another block with!). You should have a straight sided oval cylinder, six inches high.

Now start sanding until it looks like an Indy block (plenty of photo around here). I use an orbital sander; starving college students can use a block of wood wrapped in 36 grit sandpaper. Either way, this is the hard part!

Eventually it will look like this:

Image

Image

These still need a little work.

Remember, its plaster so don’t get it wet when you pull a hat over it. I wrap a plastic grocery bag around it. There are plenty of hat blocking tutorials around here.

OK that’s it! Post picture of your block when you’re done.

- Mac
User avatar
Rusty Jones
Archaeologist
Archaeologist
Posts: 390
Joined: Sat Aug 27, 2005 11:33 am
Location: Raleigh, NC, Running from the Havitos (my (ex)girlfriends' parents)

Post by Rusty Jones »

a fantastic looking first hat, lets get a pic of it on a head when you've got all the shape you can get out of it!

these guys know some handy tricks...
Indyextra1
Dig Worker
Dig Worker
Posts: 17
Joined: Fri Jul 27, 2007 9:56 pm

Post by Indyextra1 »

Thanks for the tutorial! I'll get to work on it.
The Pilot
Laboratory Technician
Laboratory Technician
Posts: 136
Joined: Thu Nov 22, 2007 1:30 pm
Location: The Great Green Pacific Northwest
Contact:

Post by The Pilot »

Indeed, thanks for the tutorial.

Perhaps when you have the time you can post a tutorial showing reblocking from start to finish? That would be very interesting.
User avatar
Dalexs
Site Admin
Site Admin
Posts: 9009
Joined: Mon Jul 08, 2002 2:49 am
Location: Jus' nath' of Bawstin
Contact:

Post by Dalexs »

One suggestion on the plaster block: Cover it in BONDO to seal it up.

You won't have to use the plastic bag treatment on it.
It also lets you finesse the shape a bit as needed.

(Do a search on BONDO here adn you might be a bit surprised! :wink: )

Nice job on the block.
User avatar
Mac
Archaeologist
Archaeologist
Posts: 236
Joined: Thu Mar 16, 2006 11:11 pm
Location: The Carolinas

Post by Mac »

Indyextra1 let me give you a word of caution. When you reblock a tapered hat, unless you have a very stretchy felt (unlikely), you are probably going to have to either trade crown height for brim width or vise versa. The extra material to fill the more full block shape must come from somewhere. You may have to settle for a slightly lower crown and/or a slightly narrower brim, but you will gain a much more straight sided bash. Here’s a very extreme example:

Prior to reblock-

Image


Lost brim-

Image



Derby, anyone?

Now don’t let this scare you, as I said this is an extreme example. This little BCF hat, in the first picture, is a 5 inch open crown, 2 3/8 inch brim, with a 9/10 inch wide ribbon. Very tiny. Judging by your picture, your brim won’t be anywhere near as short, but you may need to settle for a slightly lower crown.

For all of you BCF brown fedora hunters, if you intend to reblock the hat, get the largest hat you can possibly find so you have some leeway with the brim. Look at the first two hat photos that I posted in this thread, not the two directly above, but farther up the page. The brim in the AFTER photo has not been trimmed at all from the BEFORE photo. The brim simply disappeared into the fuller, less tapered crown.

-Mac
Indyextra1
Dig Worker
Dig Worker
Posts: 17
Joined: Fri Jul 27, 2007 9:56 pm

Post by Indyextra1 »

Thanks for the advice. I'll probably go for a shorter crown height; I think I prefer it that way. I'm mostly just going to try and get rid of the taper.
Post Reply