I'm Too Timid To Cut A Brim

In-depth discussion of the Fedora of Indiana Jones and all other hats appearing in the Indiana Jones movies

Moderators: Indiana Jeff, Dalexs

Post Reply
rogatywka
Dig Worker
Dig Worker
Posts: 18
Joined: Sun Apr 17, 2005 2:53 pm
Location: UK - Isle of Wight

I'm Too Timid To Cut A Brim

Post by rogatywka »

The heading says it all.
I'd like one-eigth inch off my Regular Fed brim.
Anyone in the UK or Europe with the guts and skill (or a brim-cutter) to do it for me, please ?
whiskyman
Museum Curator
Museum Curator
Posts: 1378
Joined: Sat Sep 10, 2005 12:30 pm
Location: Austria
Contact:

Post by whiskyman »

It's not as drastic as it sounds. You just want some sharp scissors. You can mark the felt with chalk or just eyeball it. Cut slowly, turning the hat gradually as you do it. If you have one or two uneven points, just gently buff them down with seom sand paper. When you've finished cutting, the cut will look too clean but nce you've buffed the whole edge very gently with your sandpaper you'll never tell the difference.
User avatar
binkmeisterRick
Stealer of Wallets
Posts: 16926
Joined: Thu Mar 11, 2004 3:22 pm
Location: Chattering with these old bones

Post by binkmeisterRick »

I did this to my Akubra and it turned out just fine. Just keep a couple things into consideration. First, don't rush it! Take your time. It's a good idea to take some tailors chalk or something and mark your cut line. This will help guide your cutting. Second, keep in nmind that the Raiders cut wasn't perfect. It had its character to the cut, so if you have the occasional "bump" in the brim, don't flip out. Just patiently sand it down if it bothers you. And remember it's always easier to cut more dowm later than to add it back on! Just get a good, sharp pair of fabric scissors and go slow. You'll do just fine. :wink:

bink
whiskyman
Museum Curator
Museum Curator
Posts: 1378
Joined: Sat Sep 10, 2005 12:30 pm
Location: Austria
Contact:

Post by whiskyman »

Isn't that what I said?
duc
Dig Worker
Dig Worker
Posts: 19
Joined: Wed Nov 30, 2005 1:18 pm
Location: Downeast Maine

Post by duc »

Good reiforcement of previously stated advice can only add confidence to the wary.

I thought both posts were appropriate and informative (particularly since I will be in the same boat when I order a nice cover). :wink:
Farnham54
Professor of Archaeology
Professor of Archaeology
Posts: 798
Joined: Sun Jul 20, 2003 10:48 pm
Location: Looking for clever places to re-hide Jess's TomTom

Post by Farnham54 »

I too cut my own brim, I did in in a semi-intoxicated state in my first year of University (I think it was around St. Paddy's day) marking my line with some blackboard chalk and cutting it with a little box cutter. A bit of sandpaper and some sanding, and I'm VERY pleased with the result--the brim is actually about the best part of the hat at this point! (My old fed's been through a lot!)

So, if you follow Whiskyman and Bink's directions, you should do just fine--trust me, it is REALLY easy--take your time, and remember like Bink said you can always cut more, but you can't add it back on!

Cheers
Craig
User avatar
binkmeisterRick
Stealer of Wallets
Posts: 16926
Joined: Thu Mar 11, 2004 3:22 pm
Location: Chattering with these old bones

Post by binkmeisterRick »

whiskyman wrote:Isn't that what I said?
8-[ :wink:
rogatywka
Dig Worker
Dig Worker
Posts: 18
Joined: Sun Apr 17, 2005 2:53 pm
Location: UK - Isle of Wight

Post by rogatywka »

Thanks, Folks.
Maybe I'll have a couple of slugs of Jim Beam for courage and then have a go.
User avatar
Swindiana
Legendary Adventurer
Legendary Adventurer
Posts: 3204
Joined: Sat Jul 19, 2003 11:05 am
Location: West of Scandinavia Jones, making meed for Holt
Contact:

Post by Swindiana »

And a little does a lot. And 8th of an inch sounds pretty good to start with to check if it will do the trick.

Regards,
Swindiana
CHAUVEL
Dig Worker
Dig Worker
Posts: 21
Joined: Tue Feb 01, 2005 7:18 pm
Location: australia

Post by CHAUVEL »

The sandpaper is your brim's saving grace, and jack daniels your own, should you need a little "courage". If i can do the job successfully, i reckon anyone can, trim away! cheers chauvel.
gdkenoyer
Dig Worker
Dig Worker
Posts: 8
Joined: Sun Aug 28, 2005 12:31 pm
Location: Colorado Springs CO USA

Post by gdkenoyer »

rogatywka wrote:Maybe I'll have a couple of slugs of Jim Beam for courage and then have a go.
if you're going that route, don't forget the box cutter!
User avatar
Renderking Fisk
Expeditionary Hero
Expeditionary Hero
Posts: 1896
Joined: Mon Jul 01, 2002 2:29 pm
Location: The Fedora Chronicles
Contact:

Post by Renderking Fisk »

Send it out for a reblock and see if you can have that 1/8th of an inch migrate towards the crown.

Just a thought.
User avatar
binkmeisterRick
Stealer of Wallets
Posts: 16926
Joined: Thu Mar 11, 2004 3:22 pm
Location: Chattering with these old bones

Post by binkmeisterRick »

Actually, Ren, that's a great idea! The Akubras always seemed a bit too shallow to me for an Indy hat, so adding it to the crown height could just do the trick!

bink
rogatywka
Dig Worker
Dig Worker
Posts: 18
Joined: Sun Apr 17, 2005 2:53 pm
Location: UK - Isle of Wight

Post by rogatywka »

binkmeisterRick wrote:Actually, Ren, that's a great idea! The Akubras always seemed a bit too shallow to me for an Indy hat, so adding it to the crown height could just do the trick!

bink
Would that really work ? If so, I'll be mailing the hat to Fedora for him to work his magic on it !
I'm terrified of goofing the job if I cut the brim (i.e. I might be left with a Fed fit only for polishing the car with).
User avatar
binkmeisterRick
Stealer of Wallets
Posts: 16926
Joined: Thu Mar 11, 2004 3:22 pm
Location: Chattering with these old bones

Post by binkmeisterRick »

If you reblock a hat, you can alter the brim/crown dimension in the process. Of course, if you put a hat on a block different from what the hat was originally blocked on, it will naturally change your hat specs a bit. For instance, if the original hat block used had a very round top, you'd lose some brim simply by reblocking it on a block with a less round top. I'd talk to Fedora about the possibilities to see if a reblock is a good option for you.

On the other hand, I, too, was extremely nervous about cutting my brim since I had never done so before. Trust me, you can do it. Just take the time to chalk out your lines and use a sharp pair of fabbric scissors. Be patient. That is key.

bink
IndianaJames
Professor of Archaeology
Professor of Archaeology
Posts: 765
Joined: Tue Jul 02, 2002 11:14 pm
Location: Bay Area

Post by IndianaJames »

Only 1/8th? Use sandpaper only....I did this on one of mine, and it worked great. Took a bit longer, but its realy hard to mess up....

Good luck, if you havent already cut it!

I J
Post Reply