I am in the middle of the first belly on my nylon whip. I somehow managed to drop from 8 to 6 and have it look decent.
I cannot figure out how to drop from 6 to 4. I have 3 strands on either side and I have been going U2, O1. I know the final result of dropping to 4 is U1, O1, but which strands get dropped? I tried the bottome ones, but then I had a lump and I had a spot where two strands were trying to go over the same strand and it just didn't look right.
Thanks
Jeff
Dropping strands 6 to 4
Moderator: BullWhipBorton
Re: Dropping strands 6 to 4
Hi Jeff. Why don't you try dropping the strands in the middle on both sides? If you drop both middle strands when going from 10-8 plait, why not from 6-4?
Aldo
Aldo
- riku1914
- Vendor
- Posts: 1246
- Joined: Mon Feb 07, 2011 6:38 pm
- Location: Texas, probably making whips :)
- Contact:
Re: Dropping strands 6 to 4
When i drop 10-8 i drop the next 2 that would be worked...Marhala wrote:Hi Jeff. Why don't you try dropping the strands in the middle on both sides? If you drop both middle strands when going from 10-8 plait, why not from 6-4?
Aldo
- G-Roberts
- Archaeologist
- Posts: 234
- Joined: Fri Feb 27, 2009 9:30 am
- Location: Midlands, England
- Contact:
Re: Dropping strands 6 to 4
To be honest, it doesn't matter how the belly looks. End in 6 plait on your overlay and you will be fine. I never drop to a 4 plait on my overlay any more and it works out much nicer. just make sure there is no lumps and bumps in the belly where you drop the strands.
Graeme.
P.S to drop to 4 plait you simply drop the highest strands (the ones to be worked next) Just pull them tight, lay them underneath and plait over them.
Graeme.
P.S to drop to 4 plait you simply drop the highest strands (the ones to be worked next) Just pull them tight, lay them underneath and plait over them.
- riku1914
- Vendor
- Posts: 1246
- Joined: Mon Feb 07, 2011 6:38 pm
- Location: Texas, probably making whips :)
- Contact:
Re: Dropping strands 6 to 4
Also he asked about 6 plait, i was watching one of bernie's samples i found for his dvd's yesterday, he was working on a 6 plaitG-Roberts wrote:To be honest, it doesn't matter how the belly looks. End in 6 plait on your overlay and you will be fine. I never drop to a 4 plait on my overlay any more and it works out much nicer. just make sure there is no lumps and bumps in the belly where you drop the strands.
Graeme.
P.S to drop to 4 plait you simply drop the highest strands (the ones to be worked next) Just pull them tight, lay them underneath and plait over them.
belly, and on one side ( if i saw correctly ) he did u1 o2, and on the other side he did u2 o1. That correct?
- G-Roberts
- Archaeologist
- Posts: 234
- Joined: Fri Feb 27, 2009 9:30 am
- Location: Midlands, England
- Contact:
Re: Dropping strands 6 to 4
That is correct for the overlay only to keep everything symmetrical, though each to his own. Some do u2 o1, u2 o1. Or u1 o2, u1 o2. The method for dropping from a 6 plait to 4 plait i described was going off the u2 o1, u2 o1. I should have made this clear If your dropping from the u1 o2 then drop in the bottom strands. I hope this isn't too confusing. You will get there in the end with a lot of practiceriku1914 wrote:Also he asked about 6 plait, i was watching one of bernie's samples i found for his dvd's yesterday, he was working on a 6 plaitG-Roberts wrote:To be honest, it doesn't matter how the belly looks. End in 6 plait on your overlay and you will be fine. I never drop to a 4 plait on my overlay any more and it works out much nicer. just make sure there is no lumps and bumps in the belly where you drop the strands.
Graeme.
P.S to drop to 4 plait you simply drop the highest strands (the ones to be worked next) Just pull them tight, lay them underneath and plait over them.
belly, and on one side ( if i saw correctly ) he did u1 o2, and on the other side he did u2 o1. That correct?
Graeme