Ribbon Width:: Updated

theinterchange · Post by **theinterchange** » Tue Mar 11, 2008 10:50 pm

I just got my Todd's replacement ribbon today [along with my jar of dirt.. err Fuller's] And it looks overwhelmingly narrow. I measured it at just shy of 1 1/2 inch wide. Is this even remotely screen accurate? It seems even narrower than the existing ribbon on my hat.

theinterchange · Post by **theinterchange** » Tue Mar 11, 2008 10:58 pm

I'm about to post pics of it. I bought CitRon's DP fur felt.. gassssp! Yes, it's a pretty nice hat. Take off the existing light ribbon and stupid IJ pin and it's really nice.

theinterchange · Post by **theinterchange** » Tue Mar 11, 2008 11:06 pm

It really just looks narrower.. maybe because it's not on the hat.

theinterchange · Post by **theinterchange** » Tue Mar 11, 2008 11:29 pm

I have several pics of my hat on a new thread chumming up opinions on what look to go after.

http://indygear.com/cow/viewtopic.php?t=27086

theinterchange · Post by **theinterchange** » Thu Mar 13, 2008 10:45 am

Here's the edited part. haha

I'm now trying to find a non flying v ribbon tutorial. Anyone have a link handy? Thanks

Randy

Ripper · Post by **Ripper** » Thu Mar 13, 2008 11:26 am

http://www.dalexs.whitvani.net/Dalexs_Main_Image.jpg

There ya go .

theinterchange · Post by **theinterchange** » Thu Mar 13, 2008 11:46 am

that was a link to an image..but his tutorial is for a flying v. I had already looked at it.

Ripper · Post by **Ripper** » Thu Mar 13, 2008 11:49 am

OOPS

, Well, here it is anyway... http://www.dalexs.whitvani.net/

I also am having trouble reading today. I missed the NON part of the flying v tutorial. Sorry about that, I will go back to my cornner now.

theinterchange · Post by **theinterchange** » Thu Mar 13, 2008 11:58 am

haha no worries. I can do the same thing. Thanks for your help though. That's what I like about COW everyone is willing to help the next guy.

Post by **Dalexs** » Thu Mar 13, 2008 1:13 pm

theinterchange wrote:that was a link to an image..but his tutorial is for a flying v. I had already looked at it.

What, you gotta problem with that image?

The tutorial is pretty much the same for any re-ribbin job. Just modify how you make the center pinch for the bow.

Most bows just have a basic pinch in the middle to form the fold.

theinterchange · Post by **theinterchange** » Thu Mar 13, 2008 1:14 pm

Not in the slightest. I think its a great shot. Looks really good

Post by **Dalexs** » Thu Mar 13, 2008 1:16 pm

And the bow loop you can do many different ways as well.
You juts need the patience to do all the little folding!

Fedora · Post by **Fedora** » Thu Mar 13, 2008 10:25 pm

I just got my Todd's replacement ribbon today [along with my jar of dirt.. err Fuller's] And it looks overwhelmingly narrow. I measured it at just shy of 1 1/2 inch wide. Is this even remotely screen accurate? It seems even narrower than the existing ribbon on my hat

It may be that particular run of ribbon, or it may be sized in lignes.

You can buy the 1 1/2 inch ribbon from folks like Schiff, but not in a dark, dark brown. I don't think they use the ligne system of measuring.

I could be wrong on this as it has been awhile since I bought new ribbon, other than what I get from Marc. But I have a roll of black Schiff ribbon that I pulled off some to put on a gray hat today. I measured it and it was dead on 1 1/2 inches. It said so on the end of the roll too. Much of my vintage stock comes in the ligne sizing. Seems like in this sizing, you never hit an exact 1 1/2 inches. Always above it, or below it. Fedora

theinterchange · Post by **theinterchange** » Fri Mar 14, 2008 12:21 am

ahh. it's all making sense now.