Artsee S&W replica - A "sticky" situation
Moderator: Cajunkraut
Artsee S&W replica - A "sticky" situation
So I just received my Artsee S&W replicca I got off ebay and it looks amazing. There is just one problem I have with it though and I was wondering if others had this issue and what they've done about it. It feels kinda sticky from the paint. Is there something you can spray on it to take this feeling away. I'm also worried about storing it in my new AB holster for fear of the paint coming off on the leather. advice gearheads?
Regards,
Brian
Regards,
Brian
-
- Laboratory Technician
- Posts: 144
- Joined: Sat Dec 15, 2007 8:34 am
- Location: The DelMarValous Eastern Shore
very sticky indeed
It may always be that way.
There are certain combinations of paint and plastics which never "dry". Certain paints and coatings, epoxy and silicone for example, lose some volume due to evaporation of volatiles, but actually harden or "cure" to due a chemical reaction taking place. Some plastics have ingredients that will inhibit this process and never allow the coating to fully cure. It also makes it harder to remove the paint and start over since it is partially cured. Do you know any details on the materials used to make the piece? It would be easier to know what to do in that case.
For now, try placing it on something non-stick such as parchment paper or wax paper and place it in a warm place (NOT hot) like a window sill or near a radiator etc. and wait a few days to see if it just needs more time to cure. If after this it is still tacky, it will probably be that way for a very long time. I have seen this problem where people used model paint like Testors on vinyl or other soft plastics.
If you decide to try and remove the paint, definitely find out what the casting is made from before selecting a paint remover
If you cannot find out and still want to remove the paint, proceed cautiously. Use Q-tips to test a solvent in a small area to see if it removes the paint but does not soften the plastic underneath.
Start with rubbing alcohol, then mineral spirits and finally acetone. Iwould avoid using kerosene or gasoline unless it is metal underneath.
Proceed very carefully with acetone since it can ruin many plastics. do not just dump a bunch on the part and have at it or the details in the casting may rub right off with the paint.
Good luck.
There are certain combinations of paint and plastics which never "dry". Certain paints and coatings, epoxy and silicone for example, lose some volume due to evaporation of volatiles, but actually harden or "cure" to due a chemical reaction taking place. Some plastics have ingredients that will inhibit this process and never allow the coating to fully cure. It also makes it harder to remove the paint and start over since it is partially cured. Do you know any details on the materials used to make the piece? It would be easier to know what to do in that case.
For now, try placing it on something non-stick such as parchment paper or wax paper and place it in a warm place (NOT hot) like a window sill or near a radiator etc. and wait a few days to see if it just needs more time to cure. If after this it is still tacky, it will probably be that way for a very long time. I have seen this problem where people used model paint like Testors on vinyl or other soft plastics.
If you decide to try and remove the paint, definitely find out what the casting is made from before selecting a paint remover
If you cannot find out and still want to remove the paint, proceed cautiously. Use Q-tips to test a solvent in a small area to see if it removes the paint but does not soften the plastic underneath.
Start with rubbing alcohol, then mineral spirits and finally acetone. Iwould avoid using kerosene or gasoline unless it is metal underneath.
Proceed very carefully with acetone since it can ruin many plastics. do not just dump a bunch on the part and have at it or the details in the casting may rub right off with the paint.
Good luck.
- Bufflehead Jones
- Legendary Adventurer
- Posts: 3191
- Joined: Sat Feb 14, 2004 10:11 pm
- Location: Maryland
- jedidentist
- Archaeologist
- Posts: 314
- Joined: Sun Sep 01, 2002 12:12 pm
- Location: Sudbury, MA
- Rook
- Dig Leader
- Posts: 660
- Joined: Sun Apr 01, 2007 11:11 pm
- Location: Northern Minnesota, USA
- Contact:
Sometimes, multiple layers of paint applied too close togeather will result in such a sticky surface.
Krylon at times has this problem. Also, you want to avoid mixing paint types or brands as this also may have an affect on paint curing.
I was painting Ghostbusters parts this fall and had that problem with the paint not curing fast enough, resulting in a sticky surface.
I've noticed the problem most with "metallic" finish paints overlaid with "flat" paints.
Russ
Krylon at times has this problem. Also, you want to avoid mixing paint types or brands as this also may have an affect on paint curing.
I was painting Ghostbusters parts this fall and had that problem with the paint not curing fast enough, resulting in a sticky surface.
I've noticed the problem most with "metallic" finish paints overlaid with "flat" paints.
Russ
- jedidentist
- Archaeologist
- Posts: 314
- Joined: Sun Sep 01, 2002 12:12 pm
- Location: Sudbury, MA
Hi Gang.
I wish people that want these prop guns would buy direct instead of over ebay as I never know who I am dealing with over there and can give more personalized service to you all when you tell me who you are and buy direct. The stickiness was probably coming from the old mold which has been replaced. I told of this in another thread some time ago. I have not heard of it lately though. I had to use release to get the last few out of the old mold. Problem is solved now that it has been redone with a superior material. A light coat of Krylon crystal clear should be all you would need to alleviate any stickiness on those few models that may have had some if a good soap and water bath does not do it.
I sometimes do not even know. Sometimes people want them fast and they go out as soon as they can. On these ones I can never know for sure if it cured all the way because I do not have them in my hand as soon as they are dry enough to send out.
Like I say if you want one deal direct, Everything will be better for both of us that way. I thought everyone knew that I or I would have said so sooner. I just happened to see this post so I stopped in to say what I said.
Ebay is not the way to go unless you want the feedback stuff and resolution abilities and all that at your disposal but I have sold enough now that I think people will tell you I can be trusted to come through as I have for eight years with props of various natures. Please contact me at artsee1@earthlink.net and I will get you what you need if I have it with personalized service and fast follow up emails.
Thanks.
Paul
I wish people that want these prop guns would buy direct instead of over ebay as I never know who I am dealing with over there and can give more personalized service to you all when you tell me who you are and buy direct. The stickiness was probably coming from the old mold which has been replaced. I told of this in another thread some time ago. I have not heard of it lately though. I had to use release to get the last few out of the old mold. Problem is solved now that it has been redone with a superior material. A light coat of Krylon crystal clear should be all you would need to alleviate any stickiness on those few models that may have had some if a good soap and water bath does not do it.
I sometimes do not even know. Sometimes people want them fast and they go out as soon as they can. On these ones I can never know for sure if it cured all the way because I do not have them in my hand as soon as they are dry enough to send out.
Like I say if you want one deal direct, Everything will be better for both of us that way. I thought everyone knew that I or I would have said so sooner. I just happened to see this post so I stopped in to say what I said.
Ebay is not the way to go unless you want the feedback stuff and resolution abilities and all that at your disposal but I have sold enough now that I think people will tell you I can be trusted to come through as I have for eight years with props of various natures. Please contact me at artsee1@earthlink.net and I will get you what you need if I have it with personalized service and fast follow up emails.
Thanks.
Paul